Time For a New Jeans Cut….

[Giles]

I hear you…...

[Appfaff]

lol I wondered how long we could derail that other thread haha

Sent from my iPhone using Tapatalk

[mikebarhoot]

@Megatron1505:

Alcohol fuelled intelligent design 

AFID TECHNOLOGY!  I like it!

[riffblaster general]

@Giles:

1. If we want to have selvedge side seams and a proper cut, there is a limit to the taper that can be given to the jean.  To have selvedge side seams, the outseam HAS to be parallel, so you have to take the taper off the inseam, take too much and the cut is a joke.  One of the reasons that the IH-634 is a better cut in many ways than the IH-634S, is that we don't have to worry about a parallel outseam.
2. We could use selvedge denim and dispense with the selvedge ID showing on the outseam (like the IH-461S), but that is probably a compromise too far.

I totally don't care about selvedge showing.

[Seul]

@riffblaster:

I totally don't care about selvedge showing.

[neph93]

^ me neither. But judging by SE's experience with the first run of the 301's a few years ago, enough people do so, that it may affect the financial viability of the cut.

[manufc10]

same here.  The selvedge ID not showing is not a deal breaker for me.

[spitfiredealer]

Is for me. Wouldn't dream of dropping big bucks on some without it. But then I am
Someone who likes all the extra details.

Giles those measurements for a 36 only have 0.5 taper from the knee to hem? Isn't that pretty much what the 634 have?

[browniemcghee]

Selvedge ID doesn't really matter to me, as long as the denim and construction is IH quality.  I do think that it is a big enough deal for enough people that it should probably be kept for sales sake. I want this cut to sell well so it will be made available in the new 18oz. Vintage and XHS…

Sent from my SM-G920F using Tapatalk

[Giles]

Whoops.  I have tweaked the measurements….

[Giles]

@spitfiredealer:

Is for me. Wouldn't dream of dropping big bucks on some without it. But then I am
Someone who likes all the extra details.

You simply can't have your cake and eat it.  It is impossible to give stacks of taper and retain the selvedge ID as per my explanation above….

[Dion]

Knee and thigh measurements look way better now. What hem measurement would have a tag 38 then?

[Giles]

I don't know.  I have a target, but not sure if it is technically possible…..

[Dion]

I measured the hem of my 633SII and it is ~ 8,5 (tag 38) which looks very good and clean, I must admit. So I am hoping for a similiar width.

[Giles]

Yes, but the knee and thigh will be larger on the new cut, so my concern is whether we can create that much taper and retain the selvedge ID (which is the immovable feast)

[Jordan23]

Thigh measurement is looking way better for me[emoji1319]

Enjoy ya addiction!

[spitfiredealer]

@Giles:

Yes, but the knee and thigh will be larger on the new cut, so my concern is whether we can create that much taper and retain the selvedge ID (which is the immovable feast)

So would taking the knee in a little help this?

Not as extreme as say the 555 but some kinda happy medium between the 634 and 555

[Giles]

It may do…..

[spitfiredealer]

I have had 3 pairs of 634's i have tapered all of them. The first pair i didn't change the knee measurements and it didn't work out and they are now gardening/painting jeans. The other 2 i bought the knee in to just under 9 and then down to a 8 inch hem.

size 33

[Dion]

G, do you already have a lot number?